SNS440R54U12.1W21SNS440R54U12.1W21三螺桿泵、SN系列潤滑油泵

SNS440R54U12.1W21三螺桿泵、SN系列潤滑油泵

*、確定泵的轉速：（SN 系列螺桿泵的極限轉速為＜6000r.p.m）

First, determine the pump speed （the speed limit: SN series screw pump for the < 6000r.p.m）

1．泵轉速的選擇以輸送介質的粘度和泵的規格確定轉速范圍，一般輸送高粘度介質時，

Specifications to the transmission medium viscosity and pump 1 pump speed selection range of speed, general conveying high viscosity medium,

泵應選低轉速；若粘度低，相應選擇高轉速。

Low speed pump should be selected; if the viscosity is low, the corresponding selection of high speed.

對于大規格的泵（主桿外徑∮60mm 以上）

The specifications of the pump （above the main rod diameter, 60mm）

介質粘度γ＞20°E 時，轉速以970rpm 或720rpm 為宜。

Medium viscosity γ > 20 ° E, speed to 970rpm or 720rpm is appropriate.

若γ＞80°E 如粘膠液，轉速可選n=200~500rpm

If gamma > 80 ° E such as viscose, speed optional n=200~500rpm

對于小規格的泵（主桿外徑∮60mm 以下）：

For small size pump （main rod diameter, below 60mm）:

γ＞20°E 時，n 選1450rpm 或970rpm.

Gamma > 20 ° E, n 1450rpm or 970rpm.

γ＞80°E 時，n 選300~600rpm。

Gamma > 80 ° E, n 300~600rpm.

2．由于泵的轉速愈高摩擦功率愈高，泵的磨損越大，壽命越短，如果輸送介質的潤滑

2 because the pump speed is higher friction power is higher, the greater the pump wear,short life, if the lubrication delivery medium

性較差，或含有微量雜質，應選較低轉速，使泵保持較長的使用壽命。*n＜1450rpm

Poor, or contain trace impurities, should choose the low speed, long service life of the pump.Recommended n < 1450rpm

第二、結構形式的選擇

Second, the choice of structure

結構的選擇可根據泵的運行環境和安裝環境，選擇合適的安裝形式并遵循以下的原則：

Structure selection according to the running environment of pump and the installation environment, choose to install the appropriate form and follow the following principles:

1． 輸送潤滑性油類，且溫度T＜80℃時，選擇內置軸承結構的泵。

A 1 conveying lubricating oil, and the temperature of T < 80 ℃, the choice of built-in bearingstructure of pump.

2． 輸送潤滑性較差，或溫度T＞80℃時，選擇外置軸承結構的泵。

2 delivery of poor lubrication, or temperature T > 80 ℃, select the external bearing structure of pump.

3． 輸送流動性差，粘度高的介質或?qū)λ斔徒橘|(zhì)進行加熱或保溫時，選雙層加熱泵體

3 the transport mobility is poor, high viscosity of medium or to transfer medium heating or insulation, choose double heating pump body

結構的泵。

Structure of pump.

4． 輸送高溫介質時，應選擇耐高溫的材料制成的泵或局部冷卻的泵。

The 4 conveying high temperature medium, should choose the high temperature resistant material made of pump or local cooling pump.

5． 關于泵的吸入能力可查閱樣本。

5 on the pump suction capacity of the sample.

第三、泵材料組合的選擇 見上表

Third, pump materials portfolio selection see table

第四、泵的吸上能力

Fourth, the pump suction capacity

通過降低轉速或加熱降低介質黏度的方法，可達到高的吸上性能，見NPAKP-SHR 表

By reducing speed or heating way of reducing medium viscosity, can achieve high onabsorbing properties, see table NPAKP-SHR

第五、配套電機的選配

Option fifth, matching motor

泵的型號選定后，根據樣本數據，可查到泵的軸功率N，該軸功率再加上一定的功率儲

The pump model is selected, based on sample data, can be found in the shaft power Npump, the shaft power coupled with a power storage

備后，作為選配電機的依據，一般電機功率Nm 不小于泵軸功率N 乘以功率儲備系數K 所

Later, as the basis for choosing motor, general motor power Nm is not less than the pump shaft power N multiplying power reserve coefficient K

得的值即：Nm≥K·N。K 值由下表查得。

That is worth it: Nm ≥ K · N. The K value from the table below check.

N（KW） K

N （KW） K

N≤5 1.25

N 51.25

5＜N≤10 1.2

5 < N 101.2

10＜N≤50 1.15

10 < N 501.15

N＞50 1.1

N 501.1

1．液壓行業的應用：

Application of 1 hydraulic industry:

Ø 液壓油泵

Ø hydraulic pump

Ø 潤滑油泵

Ø lubricating oil pump

Ø 燃油輸送泵

Ø fuel pump

Ø 加熱爐液壓站

Ø heating furnace hydraulic station

Ø 精軋稀油站

Ø dilute oil station finishing

Ø 粗軋稀油站

Ø dilute oil station of roughing mill

Ø HGC循環泵

Ø HGC circulation pump

Ø 精軋傳動循環泵

Ø finishing transmission pump

Ø 卷取稀油站

Ø coiling thin oil station

Ø 精軋高低壓稀油站

Ø finishing high and low pressure thin oil station

Ø 粗軋高低壓稀油站 液壓行業泵使用的流量壓力和輸油介質。

Station hydraulic industry pump flow pressure and oil medium of dilute oil Ø roughing mill of high and low pressure.

壓力：0.25MPa-2.0MPa

Pressure: 0.25MPa-2.0MPa

流量：40-2900l/min

Traffic: 40-2900l/min

介質：潤滑油、液壓油、齒輪油、透平油、美孚油、汽輪機油等

Medium: oil, hydraulic oil, gear oil, turbine oil, mobil oil, turbine oil etc.

Hydraulic pump use flow pressure industry and oil medium.

Hydraulic pump use flow pressure industry and oil medium.

Pressure: 0.25 MPa to 2.0 MPa

Pressure: 0.25 MPa to 2 MPa

Flow: 40-2900 l/min

Flow: 40-2900 l/min

Medium: oil, hydraulic oil, gear oil, turbine oil, mobil oil, turbine oil etc

Medium: oil, hydraulic oil, gear oil, turbine oil, mobil oil, turbine oil etc

2．船舶行業的應用

Application of 2 shipbuilding industry.

Ø 貨油泵

Ø cargo oil pump

Ø 掃倉泵

Ø pump

Ø 燃油泵

Ø fuel pump

Ø 燃油輸送泵

Ø fuel pump

Ø 潤滑油泵

Ø lubricating oil pump

Ø 管路吹掃泵

Ø pipeline purge pump

Ø 卸油泵

Ø unloading pump

Ø 液壓泵

Ø hydraulic pump

Ø 錨機液壓馬達驅動油泵 液壓行業泵使用的流量壓力和輸油介質。

Ø hydraulic windlass motor driven oil pump hydraulic industry pump flow pressure and oilmedium.

壓力：025MPa-3.0MPa

Pressure: 025MPa-3.0MPa

流量：40-3600l/min

Traffic: 40-3600l/min

介質：燃油、潤滑油、重油、原油、美孚油、渣油.

Medium: oil, lubricating oil, heavy oil, crude oil, mobil oil, residual oil.

Hydraulic pump use flow pressure industry and oil medium.

Hydraulic pump use flow pressure industry and oil medium.

Pressure: 025 MPa to 3.0 MPa

Pressure: 025 MPa to 3 MPa

Flow: 40-3600 l/min

Flow: 40-3600 l/min

Medium: oil, lubricating oil, heavy oil, crude oil, mobil oil, residue.

Medium: oil, lubricating oil, heavy oil, crude oil, mobil oil, residue.

3．電廠能源行業的應用

Application of 3 power energy industry

Ø 重油輸送泵

Ø heavy oil delivery pump

Ø 燃油輸送泵

Ø fuel pump

Ø 潤滑油泵

Ø lubricating oil pump

Ø 煤焦油輸送泵

Ø coal tar delivery pump

Ø 水煤漿輸送泵 液壓行業泵使用的流量壓力和輸油介質。

Ø coal water slurry conveying pump hydraulic industry pump flow pressure and oil medium.

壓力：0.25MPa-3.0MPa

Pressure: 0.25MPa-3.0MPa

流量：40-440l/min

Traffic: 40-440l/min

介質：柴油、重油、燃料油

Medium: oil, diesel oil, fuel oil

Hydraulic pump use flow pressure industry and oil medium.

Hydraulic pump use flow pressure industry and oil medium.

Pressure: 0.25 MPa to 3.0 MPa

Pressure: 0.25 MPa to 3 MPa

Flow: 40-440 l/min

Flow: 40-440 l/min

Medium: diesel oil, heavy oil, fuel oil

Medium: diesel oil, heavy oil, fuel oil

4．石油化工行業的應用

Application of 4 petroleum and chemical industry

Ø 瀝青輸送泵

Ø asphalt pump

Ø 原油輸送泵

Ø crude oil delivery pump

Ø 焦油輸送泵

Ø tar delivery pump

Ø 柴油輸送泵

Ø diesel oil transfer pump

Ø 油脂輸送泵

Ø oil delivery pump

Ø 乳化液輸送泵

Ø emulsion pump

Ø 乳膠輸送泵 液壓行業泵使用的流量壓力和輸油介質。

Ø emulsion pump hydraulic industry pump flow pressure and oil medium.

壓力：0.25MPa-3.0MPa

Pressure: 0.25MPa-3.0MPa

流量：40-9400l/min

Traffic: 40-9400l/min

介質：柴油、重油、燃料油

Medium: oil, diesel oil, fuel oil

Hydraulic pump use flow pressure industry and oil medium.

Hydraulic pump use flow pressure industry and oil medium.

Pressure: 0.25 MPa to 3.0 MPa

Pressure: 0.25 MPa to 3 MPa

Flow: 40-9400 l/min

Flow: 40-9400 l/min

Medium: diesel oil, heavy oil, fuel oil

Medium: diesel oil, heavy oil, fuel oil

第六、為了保證進泵介質的清潔性，要求泵進口前配備過濾器，過濾精度為40~80 目。

Sixth, in order to ensure the cleanness of the pump inlet medium, requires the pump inletequipped with filter, filtering accuracy of 40~80.

另外，選泵時還常由于樣本提供的泵性能參數均以表格形式或特定黏度、轉速下性能曲

In addition, pump selection is often due to the sample pump performance parameters are provided in tabular form or a specific viscosity, speed performance.

線的形式給出，所需泵的性能值，有時恰好不能直接讀出，這時可遵循如下原則，作粗

Given form line, the required pump performance values, sometimes just can not directly read,then can follow the following principles, as coarse

略估算。若需比較準確的數據，則可向?qū)I(yè)人員咨詢。

Slightly. For more accurate data, you can consult with a professional.

1．三螺桿泵的流量，壓力在相同轉速、黏度時近似成直線關系，壓力越高，流量越小。

1 of the three screw pump flow, pressure at the same speed, viscosity approximation into a linear relationship, the higher the pressure, the flux is small.

2．相同粘度、壓力下泵的流量與轉速近似成正比。

Pump flow and speed of 2 the same viscosity, pressure is approximay proportional to the.

3．相同轉速、粘度時，軸功率與壓力近似成正比。

3 the same speed, viscosity, the shaft power and pressure is approximay proportional to the.

4．相同粘度、壓力下，軸功率與轉速近似成正比。

4 the same viscosity, pressure, shaft power and speed linearly proportional to.

粘度增大時，流量和軸功率均增加，但由于其中關系比較復雜，必要時，向?qū)I(yè)人員咨詢。

Viscosity increases, the flow and shaft power increased, but the relationship is more complex,if necessary, consult with a professional.

Company name: Mount Huangshan teamon pump industry limited company

Contact person: Mr. Cheng Xiao （Sales Manager）  （）

Office address: China Huangshan City Huizhou area north of the City Industrial Park

Postal Code: 245400

 86-

 86-

 phone: 

: Hstmby01

: :

A: I want to: hstmby01

Company homepage: http; //www.hstmby.comhttp://www.luogb.com

                   http://www.cntmby.comhttp://www.tm-p.cc